Page 1. Page 2. Page 3. Page 4. Page 5. Page 6. Page 7. Page 8. Page 9. Page Page Page Page Page Page Page Page Page View and Download Potterton Prima 30F installation and servicing instructions online. Fanned balanced flue gas fired boilers. Prima 30F Boiler pdf manual. Potterton Prima F Pdf User Manuals. View online or download Potterton Prima F Installation And Servicing Instructions.

Author: Vibei Maudal
Country: Guyana
Language: English (Spanish)
Genre: Sex
Published (Last): 28 June 2018
Pages: 219
PDF File Size: 16.40 Mb
ePub File Size: 12.8 Mb
ISBN: 335-7-59496-568-9
Downloads: 66038
Price: Free* [*Free Regsitration Required]
Uploader: Malaramar

In all cases prior mamual servicinglight up the boiler and check that the pilot and main burners have a cleaneven flame and that the gas rate and main burner pressure are correctly set.

Potterton Prima 60F Manuals

If another flue outlet direction is requiredremove the appropriate flue outlet sealing plate and transfer it to the pottertno hand position. Test pilot unions for gas soundness as follows: Electrical installation and servicing should be carried out pottertin a competent person in accordance with the Potterton prima f manual. Slide flue elbow into the flue duct or lower flue adapter and secure with thumb screws. Unscrew the pilotmain burner injector and pressure test nipple from the burner.

After completing any servicing or replacement of components check for gas soundness and carry out functional checks.

Supplied in Literature Pack. For Health and Safety Information see back page. Inflammable – do not extinguish with water.

Try This PDF:   24EN43TS B PDF

Boiler Manuals: Potterton Prima 30F

Reconnect electrode lead to electrode. This method of filling a sealed system may only be used if acceptable to the Local Water Undertaking.

Potterton prima f manual phial and capillary potterton prima f manual liquid. However in the event of pilot filter blockage being suspected the complete control valve should be replaced. Unplug the gas control valve supply lead from the control box and plug it into the test socket adjacent to the boiler thermostat knobSee FIG. If a terminal is fitted less than 2m above a balconyabove ground or above a flat roof to which people have access then a suitable terminal guard should be fitted. Irritation to respiratory tract.

Pilot and Electrode Assembly including items Ensure that both ducts are cut squarely.

Pump Cover Kit potterton prima f manual – 12in. Engage the screw from accessory pack ‘ C ‘ into the pre-drilled hole in elbow extension and screw fully home. It also requires the production process to be covered by an approved and monitored system of quality assurance. Test for gas soundness around the boiler components using leak detection fluid. Remove control box securing screw and lower control box. Page 17 If there are no secondary controls fitted connect the SwL suitable junction box or Potterton Electronic Programmer.

potterton prima f boiler manual

Internal-Fitment Kitwhich is suitable for a maximum wall thickness of mm 20 in. Although the potterton prima f manual can be emptied using the drain off taps installed in the pipework around the systemto empty the boiler it is manuall to remove the drain off cap positioned within the boiler case.

Try This PDF:   PT2256 PDF

Using a leak detection fluidcheck pilot unions for gas soundness. Don’t show me this message again.


Prima boilers are certified for safety, it is manhal important that no external control devices eg. Fibre entry into the eye will cause foreign body irritation. If a three port diverter valve is used as shown in FIGS. The over-run thermostat will keep manua potterton prima f manual running when achieved check that the inlet pressure is 20 mbar See Fig 19 the boiler has shut down, as long as the combustion for inlet pressure nipple.

The elbow is replaced peima an adapter on vertically flued boilers. Cutting length remains the same for minimum or maximum clearance at the rear of the boiler.

Remove the screws securing the combustion chamber front panel and remove panel. Remove controls cover and case door as described in 1. Set the pressure gauge pointer to the system design pressure.